Are you concerned that your fluffy carpet is going to ruin the smooth swinging door, or would you rather trim the bottom of the door instead of cutting the carpet? Which saw is the best for trimming the door? If you need help with how to cut a door with a hand saw? then this article would be a perfect guide to solve your queries.
There is nothing to worry about; all you need are the right tools to get your job done. Here is a short step-by-step process that will help you out to trim your door bottom. Spare your few minutes and read the given information below!
Which Hand Saw Is More Preferable?
In plunge saws, the saw blade is plunged to a predetermined depth and engages with the workpiece. They are ideally suited for smooth, straight cuts and are often used with a track or guide for greater precision. So, the plunge handsaw will be a perfect tool to trim or cut the bottom of a door.
Moreover, you can also use a circular saw designed to cut large pieces of wood and other materials. These saws are highly popular among DIY enthusiasts and professionals for their high sawing capacity and precision.
Here is another alternative for you! In woodworking and log bucking, a crosscut saw is designed to cut wood perpendicular to the wood grain. Crosscut saws may be small or large with fine teeth close together. This crosscut saw has 10 to 16 sharp teeth per inch. Its blade is beveled to cut cleanly through the wood. To use a crosscut blade, hold it with your thumb and slowly draw it back with a few short pulls. Don’t you think it’s perfect for door trimming? The choice is yours; let’s move towards the process.
How To Cut Bottom Of The Door Easily?
Here is the quick DIY door cutting process; once you’ll follow it, you’ll get the trimmed smooth door. Maybe it will be a bit tough for you, but we’ll try to make it easy for your convenience.
Step#1: Take Measurements
In the very first step, take measurements of the door where you want to cut it. There should be precise measurements from the floor to the door at a perfect angle. Look for small pieces of wood that you can use to represent the height of the floor.
You need to overlap the plywood boards on one side of the door to represent the gap above the floor. Once you’ve marked the straight edge of the plywood with a pencil, you’ll need to slide your stack of wood apart and mark the opposite edge. That’s your cutting line.
Step#2: Detach The Door From The Hinges
A door hinge is composed of two adjoining sections, one attached to the door and another to the jamb. A downward pin holds the hinges in place. Remove the pins from the door hole and detach them. It’s a bit tough to use the nails set with the hammer to keep the pins out from the place. In other words, it should fit between the floor and the bottom hinge, with room for hammer strikes as well.
With a nail set, place the point beneath the hinge’s central pin and hammer it upwards until the pin begins to protrude at the top of the hinge.
When the pin cannot be pulled out from there, jam a paint scraper under the ridge and continue beat lightly. The door should now easily separate from the jamb as both hinges are removed.
Step#3: Get Some Support
As a piece of advice, your door needs support; the cutting would never be straight if you do it without support. Moreover, the sides of the door are likely to chip off without pressure around the cut, leaving a pretty ugly finished door.
So, what do you think about what to do now? You’ll need two scrap pieces of wood with straight edges. They should be longer than the width of your door.
The gap between the planks and your door holding surface needs to be just wide enough to pass the saw’s teeth through. Place your saw in that gap and push the planks towards the blade, so they are holding the weight of the saw.
To connect the end of the long thick timbers, you will need two shorter timbers. Now you can drill around five holes equally spaced in each of the connective timbers and attach them to each of the jig boards.
Step#4: Do Some Preparation
Your door must be made secure on the cutting table. You can either use clamp scrap wood screwed directly into the surface of the table.
After measuring from the top or bottom of your door, you will need to cut along that line which you have drawn with a pencil.
Tip: You can use the planer to lower the thickness level of wood; it can also be used to plane or flatten the surface and even the wood depending on your purpose of using it.
Step#5: Cut The Door
You have already secured your door and clamped your jig. All you have to do now is begin sawing. Make gentle, full strokes at a 90-degree angle across the grain as you continue to saw.
Step#6: Finish Your Job
Although a handsaw can produce perfectly smooth surfaces, you can still take a small block plane to ease the edge of the door so that it won’t splinter. Sandpaper wrapped around a sanding block works just as well.
Step#7: Fix The Door Back
Now you could easily place the door back into the frame and repin again. In this way, you can fix the door again. Now your door swing and open/close easily without hindering.
Wrap It Up!
A few years ago, I experienced trimming my own door, and now that I am a member of the carpentry team, my years of experience speak louder in my actions. My goal is to bring this insight to your attention and to help you understand how to trim doors.
I hope you’ll like my posted article on’ how to cut a door with a hand saw’ and the process of cutting doors will be convenient for you. You can also share your door-cutting experience with me via the comment box.